Skip to content
Windowsill Harvest

Grow Light Specs Explained: Lumens, Watts, PPFD, PAR and Kelvin

Grow light listings throw out lumens, watts, PPFD, PAR and Kelvin as if they mean the same thing. What each one actually measures, and which ones to compare.

By The Windowsill Harvest Team Published
A grow light product label listing wattage, lumens and Kelvin color temperature

Open three grow light listings and you’ll see three different sets of numbers: one brags about lumens, another leads with watts, a third throws in “full spectrum, 3000K–6500K” and calls it a day. None of them are lying, exactly — but none of them are telling you the one thing you actually need to know, which is how much usable light reaches the leaf.

This is what each term actually measures, which ones matter for growing plants, and which ones are mostly there to make a listing look impressive.

The short version, if you only read one table

What each spec measures, and what it's actually good for
Term What it measures Useful for
Watts Electricity drawn, not light produced Comparing running cost; a rough proxy for output within one product line only
Lumens / lux Brightness as the human eye perceives it Almost nothing for growing — see below
PAR The 400–700nm band of light plants actually use for photosynthesis The concept everything below is trying to quantify
PPF Fixture spec Total PAR a fixture produces per second, in µmol/s Comparing fixtures to each other
PPFD Measure this if you measure anything PAR actually arriving at a specific point (the canopy), in µmol/m²/s The number that tells you if a specific plant is getting enough light
DLI PPFD × day length, the total light dose over 24 hours Matching a crop's actual light need, since intensity and duration trade off against each other
Kelvin (CCT) A light's color, from warm/orange to cool/blue Whether the room is pleasant to sit in; a weak proxy for spectrum balance

General lighting-science definitions, not specific to any one manufacturer's listing.

Watts: what you pay for, not what the plant gets

Watts measure electricity draw, full stop. Running cost scales directly with it — a 20W light costs exactly twice what a 10W light does to run. Output is a different story: two 20W lights from two different manufacturers, using different LED chips and optics, can put very different amounts of usable light on a leaf. Watts is a reasonable way to compare running cost or to sanity-check “equivalent wattage” marketing claims against real power draw, which is the distinction that matters when you’re shopping for a clip-on light — but treat it as a weak proxy for brightness, not a real one.

Lumens and lux: built for human eyes, not leaves

This isn’t a minor technicality. Horticultural researchers Erik Runkle and Bruce Bugbee wrote a paper specifically on this mismatch, titled “Problems with Foot-candles, Lux and Lumens,” and the University of California’s Controlled Environment Agriculture program cites it for exactly this reason (UC ANR Controlled Environment Agriculture, “Lighting Illuminated”): a lumen or lux reading tells you how bright a space looks to a human, not how much photosynthesis it will support.

That said, lux isn’t useless — it’s what a free phone app actually measures, and comparing one spot in your home to another with it works fine as a rough, practical benchmark. The caveat is just that the same lux number from two different light sources (sunlight vs. an LED, say) doesn’t represent the same amount of usable light, because the two sources don’t split their output across wavelengths the same way.

PAR, PPF and PPFD: the units that actually track growth

PAR (photosynthetically active radiation) is the slice of the light spectrum — roughly 400 to 700 nanometers — that plants can actually use to photosynthesize. It’s a band, not a single number, so you’ll usually see it expressed through one of two measurements:

PPF — a fixture spec

Photosynthetic photon flux: the total PAR a light produces per second (µmol/s), measured at the source. It tells you how much usable light a fixture makes, independent of where you put it — useful for comparing two lights to each other, not for knowing what your plant is getting.

PPFD — what reaches the leaf

Photosynthetic photon flux density: how much of that PAR is actually landing on a specific spot (µmol/m²/s), at a stated distance. This is the number that answers “is this plant getting enough light,” because it accounts for both the fixture and how far away you’ve hung it.

PPFD is why distance matters as much as it does: light intensity falls off with the square of the distance from the source, so the same fixture can deliver a strong PPFD at 20cm and almost nothing useful at 40cm. A manufacturer’s PPF tells you what the light can produce in total; where you hang it decides how much of that your plant actually gets.

DLI: intensity and duration combined

PPFD is a snapshot — the light level at one instant. Plants respond to the total dose of light over a full day, which is what DLI (daily light integral) measures, in mol/m²/day.

This is the practical reason running a grow light around the clock doesn’t help: plants need a dark period regardless of DLI, so stretching the photoperiod past roughly 16–18 hours mostly just adds electricity cost without adding useful dose.

Published DLI targets vary noticeably by source and cultivar, so treat the ranges below as a starting point for comparison, not a precise target to hit:

Reported DLI ranges by crop group, from extension and research sources
Crop group Reported DLI range
Seedlings / freshly germinated 6–10 mol/m²/day
Leafy greens (lettuce, kale, spinach) 12–17 mol/m²/day
Herbs (basil and similar) 14–20 mol/m²/day
Fruiting crops (tomatoes, peppers) Hardest to hit on a windowsill 20–30+ mol/m²/day

Ranges compiled from Michigan State University Extension floriculture program DLI reference tables (canr.msu.edu/floriculture) and Purdue University Extension greenhouse lighting publications. Figures vary by specific cultivar, research source and growing method — treat as a comparison point, not a precise target. Fruiting crops in particular are difficult to hit with a small clip-on light; see the distance chart below for what a typical windowsill setup actually delivers.

For scale: 15–30cm from a typical clip-on light run 12–14 hours a day is in the right range for leafy greens and herbs, which is a big part of why those two groups dominate what actually does well on a windowsill setup, while fruiting crops like dwarf tomatoes and peppers tend to need either a much brighter fixture, a south-facing window’s direct sun on top of it, or both.

Kelvin (color temperature): mostly about your eyes, a little about the plant

Color temperature, roughly
Kelvin range Looks like Note
2,700–3,500K Warm, orange-white (standard household bulb) Comfortable to live with; a weaker practical choice for plant growth alone
4,000–5,000K Neutral white A common middle ground for full-spectrum grow lights
6,000–6,500K Cool, blue-white (overcast daylight) Closer to what drives compact, leafy growth, but can feel clinical in a kitchen

General color-temperature ranges, not measurements of a specific product.

Kelvin describes the color a light appears, not its spectrum in the detail that actually drives plant response. As a rough rule, blue-leaning light (cooler, higher Kelvin) tends to encourage compact, leafy growth, while red-leaning light (warmer, lower Kelvin) is associated more with flowering and fruiting — but a Kelvin rating alone doesn’t tell you the actual red and blue output behind it, and two lights rated the same Kelvin can still differ in how much of each wavelength they put out.

For a windowsill herb-and-greens setup, this is the same practical call already made in the clip-on grow light comparison: full-spectrum white in the 4,000–6,500K range is close enough to balanced for leafy growth, and it’s a far more pleasant color to sit next to at the dinner table than the deep purple-pink of a dedicated red/blue LED. Dedicated red/blue lights are more electrically efficient at driving photosynthesis specifically, but that efficiency gain rarely matters at the scale of a single clip-on light.

Why a “4,000 lumen, 6500K” listing still tells you so little

Put it together and the gap is clear: a listing built from lumens and Kelvin answers “how bright does this look” and “what color is it,” while leaving out “how much usable light reaches my plant” and “for how long is that enough.” That’s not necessarily a dishonest listing — PPFD and PPF testing is genuinely more expensive to run and report than a lumen rating, which is why the clip-on grow light comparison on this site is explicit about which figures are published specs rather than independently measured — but it does mean the spec sheet alone can’t tell you whether a light will actually grow something.

How to get a real answer instead of guessing

Free: a lux meter phone app

Not a true PPFD reading, but good enough to compare spots in your own home and catch an obviously underpowered setup. The full method and benchmarks are laid out crop-by-crop.

A dedicated PPFD (quantum) meter reads the actual plant-usable light directly, in the units covered above, and removes the lux-to-PAR guesswork entirely. For a single windowsill setup it’s a want, not a need — the lux app plus the distance chart covers most people — but if you’re running several lights or trying to hit a specific DLI target for a fruiting crop, it’s the tool that actually answers the question.

Handheld PAR / PPFD (quantum) light meter

Search current listings on Amazon Amazon (opens in a new tab, affiliate link)

Search link, not a specific model — we haven't tested any particular meter ourselves, so compare current reviews and accuracy claims before buying.

Frequently asked questions

Is a higher wattage always a brighter grow light? Within one product line from one manufacturer, usually yes. Across different brands, no — LED efficiency varies enough that a well-designed 15W fixture can outperform a poorly designed 25W one. Published PPF or PPFD is the only way to actually confirm it.

Do I need to buy a PPFD meter to grow herbs on a windowsill? No. A free lux app plus the wattage-based distance chart is accurate enough for a small herb-and-greens setup. A PPFD meter earns its cost once you’re running multiple lights or trying to hit a specific DLI target for a fruiting crop.

Why do some grow lights look purple-pink instead of white? Those are dedicated red/blue LED spectrums, tuned to the wavelengths chlorophyll uses most efficiently, at the cost of looking unpleasant in a living space. Full-spectrum white LEDs trade a little of that efficiency for a color that’s actually bearable to sit next to.

What’s the single most useful number on a listing, if I can only check one? PPFD at a stated distance, if it’s published. If it isn’t — and most budget clip-on lights don’t publish it — actual (not “equivalent”) wattage is the next-best proxy, cross-checked against real-world distance guidance for that wattage.

Where this fits

This is the terminology behind two gear decisions already covered on this site: which clip-on grow light to buy and how far to hang it. If you haven’t measured your actual light yet, the lux-based method and crop-by-crop targets is the place to start before shopping for a light at all.

Filed under Getting Started. Questions or a correction? Get in touch.

Keep reading